威尼斯官网app,威尼斯正规平台,威尼斯登录首页

Hi,welcome toExpomax(China)Tent Co.,Ltd.(Changzhou)!

Detailed installation steps of caravan
威尼斯官网 2015-06-01 1555 time

Installation: (before installation, the customer needs to prepare tools: two herringbone ladders, two adjustable wrenches, two hemp ropes < 30m >, 50m tape measure.)

Step 1: position the column base plate

First, make sure that the ground at the installation site is flat, and then locate the bottom plate, from

The distance from the center of the bottom slab to the center of the bottom slab is 15m in the longitudinal direction and 5m in the transverse direction. Because this tutorial is based on the caravan with a span of 15m, the longitudinal distance is 15m, and the transverse direction is the length direction of the caravan, which can be extended infinitely in multiples of 5m. Note that it must be the distance from the center to the center. After confirming the positions of the four baseplates, measure whether the distance between the diagonals is equal. If not, readjust the position. Make sure it is a rectangle instead of a parallelogram. After positioning, fix the base plate of the column at the corresponding four positions (see Section 3: tent fixing measures for the fixing method). In the same way, position and fix the other base plates in the length direction.

Step 2: place the parts

The column, corner joint, inclined beam a section, inclined beam B section (note that two inclined beams are required for the span of more than 14 meters), inclined beam adapter (used to connect inclined beam a section and inclined beam B section, and there is no such component below the span of 14 meters). The top node is placed according to the figure below, and all components form a gable, that is, the so-called span that face herringbone frame. Place other gable parts according to the same principle, and pay attention to placing them on the ground in one direction.

Step 3: connect a / B section of inclined beam

Insert the inclined beam a section into the inclined beam adapter of the inclined beam B section (we will assemble the inclined beam adapter to the inclined beam B section when we pack), and bolt two screws (Note: the small hole will not be installed first)

Step 4: install the top node

Connect the AB section of the connected inclined beam with the top node, bolt in the screws, and

篷房安装完成后整体效果图

The distance from the center of the bottom slab to the center of the bottom slab is 15m in the longitudinal direction and 5m in the transverse direction. Because this tutorial is based on the caravan with a span of 15m, the longitudinal distance is 15m, and the transverse direction is the length direction of the caravan, which can be extended infinitely in multiples of 5m. Note that it must be the distance from the center to the center. After confirming the positions of the four baseplates, measure whether the distance between the diagonals is equal. If not, readjust the position. Make sure it is a rectangle instead of a parallelogram. After positioning, fix the base plate of the column at the corresponding four positions (see Section 3: tent fixing measures for the fixing method). In the same way, position and fix the other base plates in the length direction.

Step 2: place the parts

The column, corner joint, inclined beam a section, inclined beam B section (note that two inclined beams are required for the span of more than 14 meters), inclined beam adapter (used to connect inclined beam a section and inclined beam B section, and there is no such component below the span of 14 meters). The top node is placed according to the figure below, and all components form a gable, that is, the so-called span that face herringbone frame. Place other gable parts according to the same principle, and pay attention to placing them on the ground in one direction.

Step 3: connect a / B section of inclined beam

Insert the inclined beam a section into the inclined beam adapter of the inclined beam B section (we will assemble the inclined beam adapter to the inclined beam B section when we pack), and bolt two screws (Note: the small hole will not be installed first)

Step 4: install the top node

Connect the AB section of the connected inclined beam with the top node, bolt in the screws. 

  • Contact:
    Sandy Tao
  • Mobile:
    +86 18861290287
  • Tel:
    0519-89996233
  • Fax:
    0519-89996233
  • Address:
    No.179 lujiatou,youguan town,ChangZhou,JiangSu province,CHINA

Pay attention to our
CopyRight ? 2017 Expomax(China)Tent Co.,Ltd.(Changzhou) All Rights Reserved   ICP:苏ICP备14026886号-1
【statement】
XML 地图 | Sitemap 地图